UKAS Accredited
Concrete Site Testing
FIND OUT MORESimtec - Plate Testing Services
Simtec Materials Testing was established in 2007 with a workforce that already had many years of experience in the construction and civil engineering industry. Our committed and pioneering approach to standards and compliance has allowed us to build a strong reputation in the industry.
Simtec Materials Testing offer CBR and plate load testing for clients who require load bearing information on sub base materials when undertaking road pavement design.
CBR tests are carried out on fine materials whereas plate load tests are done when the underlying materials are coarse. The result of the plate load test gives an equivalent CBR value.
CBR and plate load testing can also be used to assist in designing temporary foundations for construction compounds, piling mats or crane location on a particular site.
Our reliable, professional service and exemplary safety record comes competitively priced with no minimum charge. Call us today to find out more or for some friendly advice and guidance on your requirements.
Plate Testing Overview
Most contracts for highway works and earthworks include a requirement for a plate test at various stages of construction. This is essential to ensure adequate support for subsequent works and additional layers of material.
The test, properly called the “Plate Bearing Test”, is carried out using a thick metal plate which is pushed into the ground under test using a hydraulic jack. Both the increasing applied load and the subsequent settlement created are closely monitored and used to produce a graph. From this graph the CBR value (California Bearing Ratio) can be calculated, and other material characteristics established. The required CBR value is generally quoted in the contract documents and works cannot normally be continued until it is demonstrated that this target value has been met.
Simtec are well equipped and able to provide this service quickly and efficiently. Each test takes 15 to 20 minutes and requires kentledge in the form of a plant vehicle to jack against.
*Our UKAS accreditation is limited to those activities described on our UKAS schedule of accreditation found here.
Plate Load Testing
UKAS Accredited BS and BS EN Standard Testing
UKAS accreditation is assessed on individual tests, and Simtec endeavour to gain accreditation for most site and laboratory tests as and when there is a demand in the marketplace. We currently hold accreditation for around 60 individual test methods, and it is constantly increasing. Our schedule was recently transitioned to ISO/IEC 17025:2017.
Simtec provides a high-quality service from well equipped, UKAS accredited laboratories in Leicestershire.
Our laboratory testing is constantly monitored internally and regularly audited to provide the level of service expected by our clients. Our comprehensive range of tests is UKAS accredited to guarantee the quality and validity of results and subsequent test reports.
Services Simtec Offer
Simtec offer services in all the following disciplines and more:
- Highways and construction
- Environmental and waste management
- Water, drainage and utility works
We undertake testing of earthworks, concrete, unbound and hydraulically bound aggregates, bituminous mixtures and recycled aggregates. Additionally, we can provide a range of in-situ testing on both placed and naturally occurring materials, including diamond coring*, surface regularity, skid resistance, plate bearing, incremental loading tests, geotechnical investigation, drainage testing and dust monitoring.
*Our UKAS accreditation is limited to those activities described on our UKAS schedule of accreditation found here. Diamond Coring* is outside of our UKAS accredited scope of works
Frequently Asked Questions
Weather does not adversely affect testing, however rain over a prolonged period will distort CBR values. Avoid testing when the surface is frozen or affected by frost and snow or is saturated.
Payment can be made either by cheque made out to "Simtec Materials Testing Ltd" or by BACS transfer. Our office will pass on the relevant bank details to make the transfer.
Testing at each location typically lasts 30 mins. Individual test duration will vary according to the ground conditions.
If no laboratory samples are taken from site we aim to get your reports to you within 48 hours but preliminary results can usually be given after the test is complete to give you an idea of compliance.
Usually a week to guarantee a slot although on occasion we can work around the client to fit in urgent jobs or last minute requests.
If you require advice about any aspect of our operation please call our contact number. our staff will be happy to connect you with someone appropriate to answer your question. Further advice is available regarding laboratory and site testing as well as test results and their implication.
The Simtec approach
Fast, accurate assurance when you need it.
We act as the grease-in-the-wheels of the construction industry, ensuring work progresses at pace with unnecessary costs avoided. Since 2007 we have established ourselves as the trusted name in construction materials testing, building a professional, practical and methodical business culture from the top down.
Our approach is simple – we believe shared knowledge is the foundation on which we all progress. That’s why we have documented and routinely share best practices with our partners and clients to minimise everyone’s exposure to risk.
Every contract we undertake is measured against the Simtec Optimum Compliance Benchmark –data consisting of best practice criteria, designed to help you achieve consistently high compliance approval and avoid cost of delay or remedial work. We’re proud that the integrity, rigour and safeguarding we provide has established Simtec as a trusted testing partner to firms across the UK’s construction sector.
